P599 FPGA-based USM Main PMC PCI Mezzanine Card The P599 is an USM main PMC mezzanine card with onboard FPGA. USM Universal Submodules make PMC modules more flexible than ever. The main PMC P599 gets its specific function through the IP cores implemented inside its onboard FPGA. This function can be changed at any time through implementation of different IP cores. The corresponding line drivers are realized on the USM which is simply plugged on the P599. The same USM may also be used on XMCs, conduction-cooled PMCs or M-Module main modules. A new design is then limited to the USM module and the FPGA content andtherefore saves development time and costs. A Nios soft processor implemented in the Cyclone II FPGA by Altera provides local intelligence where needed. The I/O signals are led to the USM and then to a SCSI connector at the front of the P599. The growing range of Wishbone-based standard IP cores from duagon comprise different UARTs, Ethernet, fieldbus interfaces, graphics, digital I/O etc. For users who like to write and/or implement specific IP cores on their own a complete FPGA USM development kit is available. The USM concept has been developed for harsh environments. Therefore, the P599 uses robust connectors to the USM, while all other components are soldered, and operates in a -40 to +85 °C temperature range with qualified components. The P599 is aPMC mezzanine card suitable for any PMC compliant host carrier board in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC. Appropriate PMC carrier cards in 3U, 6U and other formats are available from duagon or other manufacturers. Main PMC for USM Universal Submodules 1 USM slot 1 FPGA 33,216 LE (for user-defined I/O and Nios soft core) 32 MB DDR2 SDRAM 2 MB Flash -40 °C to +85 °C

P506 Quad CAN Bus Interface PMC PCI Mezzanine Card The P506 is a mezzanine PMC with four CAN interfaces supporting CANopen and CAN Layer 2. The P506 is a 32-bit/33MHz PMC with four CAN interfaces. They support CAN Protocol Version 2.0A/B, standard and extended data frames, remote frames, 0..8 bytes data length and a programmable data rate of up to 1 Mbit/s. The P506 is based on the USM concept. USM Universal Submodules make PMC modules more flexible than ever. The CAN bus interfaces are realized via four IP cores implemented inside its onboard FPGA. This function can be changed at any time through implementation of different IP cores. The corresponding line drivers are realized on the USM which is simply plugged on the P506. The I/O mezzanine module is suitable for any PMC compliant host carrier board in any type of bus system, i.e. CPCI, VME or on any type of stand-alone SBC in telecommunication, industrial, medical, transportation or aerospace applications. It offers long-term availability for at least 10 years and is qualified for operation in the extended temperature range. 32-bit/33-MHz PMC Full CAN/Extended CAN 4 independent channels ISO high-speed coupling Up to 1 Mbit/s data transfer rate CANopen master and slave support CAN Layer 2 support Isolation between channels Compliant to ISO 11898-1 and ISO 11898-2 -40 °C to +85 °C

F603 Side Card USB/COM 3U CompactPCI The F603 is a 4HP mixed USB/COM extension card for 3U Intel based CompactPCI single-board computers. It can be used in combination with the F14 and compatible CPU boards. The F603 is a 4HP mixed USB/COM extension card for 3U Intel based CompactPCI single-board computers. It can be used in combination with the F14 and compatible CPU boards. Modern Intel based boards increasingly support USB interfaces as an exclusive universal connection of devices such as keyboard, mouse, CD-ROM, floppy etc. Especially in industrial applications however many existing systems still use legacy I/O. Thus, the F603 provides one COM interface as well as two more USB 2.0 interfaces that extend the Single-Board Computer functionality to 4 USB ports at the front panel. In addition an onboard 2.5" SATA hard-disk slot and a CompactFlash slot is available on the F603. The F603 is directly plugged to the right side of the respective single-board computer. A robust connector makes for high mechanical stability. It is delivered with an 8HP front panel, replacing the 4HP front panel of a 3U single-board computer and thus resulting in a solid one-piece front panel. 4 HP extension for 3U Intel SBCs F14, F15, F17, F18, F19P, F21P 1 RS232 2 USB 2.0 2.5" SATA hard-disk slot CompactFlash slot

F213 PMC Carrier Board for 1 Mezzanine Card 3U CompactPCI The F213 is a rugged single Eurocard CompactPCI carrier board supporting the PMC mezzanine standard or, as an option, the Mini PCI card standard. The F213 is a rugged single Eurocard CompactPCI carrier board supporting the PMC mezzanine standard or, as an option, the Mini PCI card standard. The standard version of the F213 offers one PMC slot with a 32-bit and 33-MHz or 66-MHz data transfer rate. Using mezzanine carrier cards like the F213 is a fast and easy way to extend the functionality of any CompactPCI system based on the huge offer of PMC modules available on the market. The F213 is designed for -40°C to +85°C operation temperature using qualified components and prepared for conformal coating in order to be used also in harsh and mobile environments. The final environmental qualification depends on the respective cards used on the carrier. 4 HP 32-bit/33-MHz CompactPCI 1 32-bit/33-MHz or 66-MHz PMC slot Optional Mini PCI card slot -40 °C to +85 °C

A20 2eSST Intel Core 2 Duo CPU Board 6U VMEbus The A20 is a 6U single-slot multi-core VMEbus SBC supporting a variety of Intel Core Duo and Core 2 Duo processors and offering two XMC or PMC slots. The A20 6U single-slot VMEbus SBC supports a variety of Intel Core Duo and Core 2 Duo processors from the high-end 1.5 GHz L7400 to the low-voltage dual-core versions down to a selection of single-core Celeron M types. It is designed especially for systems which require high computing and graphics performance and low power consumption in a typical Windows environment, under VxWorks or Linux. Using the TSI148 bridge controller the CPU card provides 2eSST performance levels while maintaining backwards compatibility with older standards such as VME64 and VME32. The standard I/O available at the front panel of the A20 includes graphics on a VGA connector, one Gigabit Ethernet and one USB 2.0 interface. As an option a COM interface on an RJ45 connector can be provided instead of the USB interface. As rear I/O the A20 provides seven USB interfaces, one SATA port and PMC rear I/O. A second SATA interface for connection of an onboard hard disk or for building up RAID systems is provided on-board instead of one PMC or XMC. One PATA interface supports the onboard CompactFlash slot. The working memory comprises up to 4 GB DDR2 DRAM which is soldered to guarantee optimum shock and vibration resistance. A total of six PCI Express lanes for high-speed communication (such as Gb Ethernet) are supported on the A20. One x1 PCIe link is used for the onboard Ethernet interface, three x1 links support the XMC slots, one x1 link supports the PMC slots via a PCI Express to PCI-X bridge and one x1 link is used for connection of the VMEbus bridge. The PMC slots support 64bit/66MHz (PCI-X). Supervision of the processor and board temperature as well as a watchdog for monitoring the operating system complete the functionality of the SBC. The A20 comes with a tailored passive heat sink within 4 HP height. However, forced air cooling is always required inside the system. Equipped with Intel components exclusively from the Intel Embedded Line, the A20 has a guaranteed minimum standard availability of 5 years. Its robust design make the A20 especially suited for rugged environments with regard to extended operating temperature, shock and vibration according to applicable DIN, EN or IEC industry standards. It is also ready for coating for use in humid and dusty environments. The wide range of industrial applications include for example monitoring, vision and control systems as well as test and measurement. Main target markets comprise industrial automation, security and infotainment, traffic and transportation, shipbuilding, medical engineering and robotics. Intel Core 2 Duo L7400 Core Duo U2500 or L2400 1-slot 2eSST VMEbus master and slave Up to 4 GB DDR2 DRAM soldered 2 SATA, 1 PATA interface 1 VGA at front 1 Gb Ethernet at front 1 USB at front 2 XMC or 2 PMC PCI Express six x1 links Board controller

F18 Intel Core 2 Duo CPU Board 3U CompactPCI The F18 is a 3U CompactPCI SBC equipped with the Intel Core 2 Duo T7500. Equipped with the Intel high-performance Core 2 Duo processor T7500 running at 2.2 GHz, the F18 is a versatile 4HP/3U (single-slot, single-size Eurocard) single-board computer based on the latest multi-core processor architecture from Intel with full 64-bit support. The CPU card delivers an excellent graphics performance and is designed especially for embedded systems which require high computing performance with low power consumption. The F18 offers a 32-bit/33-MHz CompactPCI bus interface and can alsobe used without a bus system. In combination with a specific side card it can also perform system-slot functionality in a CompactPCI Express system. A total of six PCI Express lanes for high-speed communication (such as Gigabit Ethernet, graphics) are supported on the F18. 2 x1 PCIe links are used for the two onboard Ethernet interfaces. 4 x1 or 1 x4 PCIe links are available on a specific side card. The DDR2 DRAM is soldered to F18 to guarantee optimum shock and vibration resistance. A robust IDE CompactFlash device offers nearly unlimited space for user applications. In addition to parallel ATA, three serial ATA lines are available. The standard I/O available at the front panel of F18 includes VGA graphics, two PCIe-driven Gigabit Ethernet interfacesas well as two USB 2.0 ports. The F18 can be extended by different side cards. Additional functions include two digital video interfaces for flat panel connection via DVI (multimedia), a variety of different UARTs or another four USB 2.0 ports, SATA forhard disk or RAID connection and HD audio.The F18 is also prepared for rear I/O where for example another two USB 2.0 ports can be connected. Two watchdogs for thermal supervision of the processor and board temperature as well as for monitoring the operating system complete the functionality of the F18. The F18 operates in Windows and Linux environments as well as under real-time operating systems that support Intel's multi-core architecture. The Award BIOS was specially designed for embedded system applications. Equipped with Intel components exclusively from the Intel Embedded Line, the F18 has a guaranteed minimum standard availability of 5 years. The F18 is suited for a wide range of industrial applications, e.g. for monitoring, vision and control systems as well as test and measurement. Main target markets comprise industrial automation, multimedia, traffic and transportation, aerospace, shipbuilding, medical engineering and robotics. The F18 comes with a tailored passive heat sink within 4 HPheight. The robust design of the F18 make the board especially suited for use in rugged environments with regard to shock and vibration according to applicable DIN, EN or IEC industry standards. The F18 is also ready for coating so that it can be used inhumid and dusty environments. Intel Core 2 Duo T7500, 2.2 GHz Dual core 64-bit processor Full 64-bit support (4 GB memory addressable) PCI Express six x1 links 4 HP system master or stand-alone 32-bit CompactPCI or cPCI Express Up to 4 GB DDR2 DRAM soldered CompactFlash slot 3 SATA interfaces Video via VGA and 2 SDVO 2 Gigabit Ethernet (PCIe) Up to 8 USB 2.0 High Definition audio Board controller

F14 Intel Pentium M CPU Board 3U CompactPCI Equipped with the high-performance Intel 2-GHz Pentium M down to the 1-GHz ultra low voltage Celeron M processor, the F14 is a 4 HP/3U CompactPCI board, designed for embedded systems with high computing/graphics performance and low power consumption. Equipped with the high-performance Intel 2-GHz Pentium M down to the 1-GHz ultra low voltage Celeron M processor, the single-board computer F14 is a versatile 4 HP / 3U (single-slot, single-size Eurocard) CompactPCI board, designed especially for embedded systems which require high computing and graphics performance and low power consumption. All versions of the CPU card come with tailored passive heat sinks within 4 HP height. Depending on the processor version forced air cooling is required inside the CompactPCI system. The F14 is suited for a wide range of industrial applications, for example for monitoring, vision and control systems as well as test and measurement. Main target markets comprise industrial automation, multimedia, transportation (railways, commercial vehicles), aerospace, shipbuilding, medical engineering and robotics. The robust design of the F14 together with the low-power Pentium M processors make the board especially suited for use in rugged environments in mobile applications with regard to temperature, shock, vibration, humidity or dust according to the applicable DIN, EN or IEC industry standards. The F14 is also ready for coating so that it can be used in humid and dusty environments. The F14 offers a 32-bit/33-MHz interface to the CompactPCI bus and can alternatively also be used without a bus system. In combination with a specific side card it can also perform system-slot functionality in a CompactPCI Express system. Four PCI Express links for high-speed communication requirements (such as Gigabit Ethernet, graphics) are supported on the board. The DDR2 DRAM is soldered to F14 to guarantee optimum shock and vibration resistance. An IDE-driven robust CompactFlash device offers nearly unlimited space for user applications. Apart from parallel ATA support, two serial ATA lines are also available. The standard I/O available at the front panel of F14 includes graphics on VGA connector, two PCIe-driven Gigabit Ethernet interfaces (alternatively 1 Gigabit / 1 Fast Ethernet) as well as two USB 2.0 ports. The F14 can be extended by a side card to 8 HP. I/O functions realized on the side card include two digital video outputs for flat panel connection via DVI, another four USB 2.0 ports and HD Audio. The F14 is also prepared for rear I/O where for example another two USB 2.0 ports can be connected. Two watchdogs for thermal supervision of the processor and board temperature as well as for monitoring the operating system complete the functionality of the F14. The F14 operates in Windows and Linux environments as well as under major real-time operating systems like VxWorks or QNX. The Award BIOS was especially designed for embedded system applications. Equipped with Intel components that come exclusively from the Intel Embedded Line, the F14 has a guaranteed minimum standard availability of 5 years. ULV Celeron M 373, 1 GHz Up to Pentium M 760, 2 GHz PCI Express four x1 links 4 HP system master or stand-alone 32-bit CompactPCI or cPCIe Up to 2 GB DDR2 DRAM soldered CompactFlash slot 2 SATA interfaces Video via VGA and 2 SDVO 2 Gigabit Ethernet (PCIe) Up to 8 USB 2.0 High Definition audio Board controller -40°C to +85°C screened versions

F12N PowerPC MPC5200B CPU Board 3U CompactPCI Equipped with the MPC5200B PowerPC, the F12N single-board computer is a versatile 3U Eurocard CompactPCI board that operates at up to 400 MHz and 700 MIPS. Equipped with the MPC5200B PowerPC, the F12N single-board computer is a versatile 3U Eurocard CompactPCI board that operates at up to 400 MHz and 700 MIPS. The F12N is designed especially for systems which require low power consumption and mechanical robustness. With the processor consuming less than 1 W, the board is delivered for -40 to +85°C operation temperature. All components on the board are soldered. The F12N is thus well placed as a rugged computing platform for mobile applications, offering thewhole world of Linux based software and real-time operating support for VxWorks and QNX. The CPU card is equipped with an onboard soldered SDRAM of up to 256 MB and up to 1 GB NAND Flash as well as with 16 MB additional SDRAM, up to 8 MB boot Flash and 2 MB battery-backed SRAM. The SBC provides two Fast Ethernet interfaces, one serial line and USB 1.1 at its front panel. As an alternative to RJ45, D-Sub connectors guarantee reliable functions also in harsh environments. Two CAN controllers with V2.0A/BCAN protocol are included in the MPC5200B and are accessible via SA-Adapters. A second serial interface can be accessed using an SA-Adapter on the F12N. (E)IDE and GPIO are also on board. The large FPGA on the F12N allows to realize additional user-defined functions such as graphics, touch, further serial interfaces, further CAN bus controllers, binary I/O etc. for the needs of the individual application in a very flexible way. Before boot-up of the system, the FPGA is loaded from boot Flash. Updates ofthe FPGA contents can be made inside the boot Flash during operation. The FPGA functions can be physically implemented by using SA-Adapters. A maximum of 8 SA-Adapters can be used on the F12N and I/O can be made accessible at the front panel. Equipped with a PCI-bridge chip, the F12N offers a full CompactPCI interface (system slot functionality) for reliable system expansion. The F12N comes with MENMON support. This firmware/BIOS can be used for bootstrapping operating systems (from disk, Flash or network), for hardware testing, or for debugging applications without running any operating system. 32-bit/33-MHz cPCI system slot, 4 HP MPC5200B / 384 MHz FPGA 18,752 LEs (approx. 225,000 gates) Up to 256 MB onboard DDR SDRAM Up to 8 MB boot Flash, NAND Flash 2 MB SRAM, 16 MB graphics memory Dual Fast Ethernet, COM, USB (front) Dual CAN bus controller FPGA for user-defined I/O functions MENMON BIOS for PowerPC cards -40°C to +85°C with qualified components

B202S M-Module Carrier Board 3U VMEbus The B202S is an M-Module carrier board for universal peripheral input/output applications on the VMEbus. The B202S is an M-Module carrier board for universal peripheral input/output applications on the VMEbus. M-Modules are screwed tightly on the carrier board, but the board needs only one slot on the VMEbus. duagon's B202S offers VMEbus developers instant access to more than 70 different M-Modules for I/O in fields such as process I/O, measurement, instrumentation, motion control, communication, and development. 2 M-Module slots 1 VMEbus slot

BL50S Rugged Box PC for Transportation with AMD G-Series Railway & Automotive Embedded Computer for Storage Control The BL50S is a rugged, fanless EN 50155 railway and E-Mark automotive box computer, based on an AMD dual-core T48N. It is used as train maintenance, surveillance and diagnosis computer, and - thanks to its built-in storage capacities - as railway video recorder and content server. For CCTV and Other Storage-Intensive Applications The BL50S is a maintenance-free fanless box computer that has been designed for embedded storage systems such as content servers or video recorders, e.g., for CCTV applications. It offers two external SATA shuttles with hot-plugging support. Wired and Wireless Communication At the front the rugged BL50S provides five Gigabit Ethernet interfaces. Four of these ports share one Gigabit Ethernet port from the chipset via a switch, while one port is used exclusively as Gigabit Ethernet uplink. The four ports routed over the switch support Power-over-Ethernet. One PCI Express Mini Card slot with two SIM card slots offers the possibility to implement a wide range of wireless communication functions. This includes mobile service standards up to LTE (4G) and derivates, WLAN IEEE 802.11 and derivates as well as positioning systems GPS or GLONASS. Fanless Operation for Mobility Applications The BL50S is designed for fanless operation at temperatures from -40 °C to +70 °C (+85 °C for up to 10 minutes), its special aluminum housing with cooling fins serves as a heat sink for the internal electronics and in this way provides conduction cooling. The system comes with its own integrated class S2 wide-range power supply with 24 V DC and 36 V DC nominal input voltage and a power consumption of 30 W. It complies with EN 50155 and ISO 7637-2 (E-mark for automotive). The power can be switched on and off using an ignition signal on the power connector, and a run-down time after switching off the ignition signal can be adjusted by software. Solid Processing Performance & I/O The BL50S is powered by an AMD Embedded G-Series APU (Accelerated Processing Unit), the T48N, running at 1.4 GHz. The G-Series combines low-power CPUs and advanced GPUs, in this case an AMD Radeon HD 6310, into a single embedded device. The use of the Embedded G-Series makes for high scalability in CPU (single/dual core) and graphics performance (various Radeon GPUs or none at all). The box PC comes with 2 GB of DDR3 SDRAM and has SD card and mSATA slots. It supports one DisplayPort interface with a resolution of 2560 × 1600. In addition, a multitude of other I/O is available at the front, including two USB 2.0 and variable slots for legacy serial I/O (e.g. RS232) or CAN bus. The combination of the various CPU/GPU options with the available selection of external interfaces makes for an extremely flexible system design that can quickly be tailored to a vast number of applications. AMD Embedded G-Series APU RAID 0/1, hot-pluggable on 2 HDD/SSD shuttles 4-port Gb Ethernet switch with PoE 1 Gb Ethernet uplink 1 PCIe Mini Card slot with 2 micro-SIM slots WLAN, 4G LTE, GPS or GLONASS 2 slots for IBIS, RS232, RS485, RS422 24 and 36 V DC nom. class S2 PSU, with ignition -40 °C to +70 °C (+85 °C), fanless Compliant to EN 50155 (railways) Compliant to ISO 7637-2 (E-mark for automotive)